
Most houses have more concrete in the driveway than anywhere else, and it carries the most weight. New concrete driveways, wider drives, parking pads and full replacement of drives that have cracked, sunk or broken up are all jobs Grapevine Custom Concrete handles for Grapevine, TX homes.
Concrete driveways around here deal with clay that swells after a wet spring and shrinks in a dry August, plus the weight of every car, delivery van and trash truck that turns in. A drive poured on a thin or uneven base starts showing it within a few seasons.
Breaking out the old slab, checking the ground, building a firm base and setting forms with the right fall toward the street are the parts of the job that matter most.
If only a panel or two is the problem, concrete repair may be enough. If the drive also needs a matching front walk, the sidewalks and walkways page covers that side.
To get a price, phone 817-776-4658. A rough size and a photo or two of the old drive are a good start.
Free quote. No obligation.
Two drives with the same square footage can price quite differently once the ground, the access and the old concrete are taken into account. That is why the number comes after someone has walked yours.
If the drive will tie into a new front walk, say so early. The two slabs meet at a joint, and where it falls is easier to plan before either is formed.
The steps below describe how the work is generally done; ask what the quote for your drive includes.
The old drive is broken into pieces and removed. With it gone, the ground underneath can be checked for wet spots, soft clay and voids where soil has washed out. Weak areas are dug out and replaced with material that compacts well.
A base layer is spread and compacted so the slab has an even bed. Forms are set to the finished height, with a fall that carries water toward the street and away from the garage door. Expansion material goes where the drive meets the house, the garage slab or the sidewalk.
Most concrete driveways get some kind of reinforcement, such as steel bar, welded wire or fibers in the mix. It does not stop cracks from forming, but it helps hold the pieces together and level if they do.
The concrete is placed, struck off level with the forms and floated. A broom finish gives tires grip. Control joints are tooled in while it is wet or saw-cut once it has hardened enough, laid out so each panel is roughly square.
Hot afternoons and cold nights are the two risks for a fresh drive, so its first days get watched. People can usually walk on it well before cars can drive on it.
Once the drive is coming out, there are a few decisions to make. Do you want it wider at the garage, or a pad on one side for a third car or a trailer? Should the walk to the front door tie in with a curve? A plain broom finish keeps it simple; exposed aggregate or a stamped border dresses it up.
Want a matching surface out back? The concrete patios page covers that.
A finished drive running to the street, a house front with its new slab, and concrete coming down the chute.



Often it can. A play slab beside the drive is formed as its own section with a joint between the two, and a hoop post usually gets its own footing, which is easier to set before the concrete goes in. If you are in an HOA, check what it says about hoops that can be seen from the street.
Usually. A new strip is poured alongside, tied to the old slab where that makes sense, with a joint between them. The new concrete will look brighter at first, so if the old drive is worn, some people replace the whole thing so it matches.
Ask Building Inspections. The city’s published answers single out drives that tie into the curb or street, and it has an application for sidewalks and drive approaches. They can tell you what applies to your address.
On the street or at a neighbor’s, for longer than most people expect. The garage is cut off from the day the old drive is broken out until the new concrete is strong enough to carry a car. Some HOAs limit street parking, so check yours, and ask when the new drive is ready for cars.
Ready to price a new drive? Phone 817-776-4658, or send the form and we will set up a time to look.
Local weather and permit notes are on the Grapevine home page, and the number and a short form are on the contact page.